Search You searched for “ADA4522-4ARZ” Filters Filters Product Categories Amplifiers 2 Show More Resources Show More Industry Solutions Consumer Technology Solutions 1 Energy Solutions 1 Healthcare Solutions 1 Industrial Automation 2 Instrumentation and Measurement Solutions 2 Show More Tools and Models Technology Solutions Sensor Interface Solutions 1 Show More Site Section Result Type Blog Post3Comment8Docs & FAQs38Forum Reply462Forum Thread144Webinar4Show More Groups, Forums & Libraries 8052 Core Products2ARM7 Core Products1Amplifiers26Data Converters1Design Support AD9371/AD93752Design Tools and Calculators2Differential Amplifiers and ADC Drivers102EZ Blogs11Show More Author ADIApproved78Alexxx4AnneM10EZAdministrator15Emman.A29Fdelaram9FormerMember18GenevaCooper9Show More Tag amplifiers106Operational Amplifiers (Op Amps)83Zero-Drift Op Amps49ada4528-124hardware20Low Input Bias Current Op Amps (≤100 pA)19ada452814Precision A/D Converters13Show More Results on Analog.com 2 Results on EngineerZone 659 Results on Analog.com 2 Relevance Relevance Oldest First Newest First Sort by ADA4522-4Recommended for new designsProductZero-Drift Op AmpsQuad 55 V, EMI Enhanced, Zero Drift, Ultralow Noise, Rail-to-Rail Output Operational Amplifier PDFDatasheetDocumentationAsk the CommunitySample & BuySample & BuyADA4622-4Recommended for new designsProductJFET Input Op Amps30 V, 8 MHz, Low Bias Current, Single-Supply, RRO, Precision Quad Op Amp PDFDatasheetDocumentationAsk the CommunitySample & BuySample & Buy <<<1>>> Results on EngineerZone 659 ADA4522-1 Datasheet Specs ClarificationForum ThreadAnswered Operational Amplifiers11 February, 2024Hi, I am looking at using this ADA4522-1 amplifier as a buffer for a low noise reference in the -12V to 12V range due to good dc offset and low noise. The datasheet mentions the railing issue and that it needs a fast supply and does not handle well … Operational Amplifiers (Op Amps)Datasheet/SpecsamplifiersADA4522-1Zero-Drift Op AmpsADA4522-1 biasingForum ThreadAnswered Operational Amplifiers02 October, 2023Hi Everyone, I was trying to implement a TIA with ADA4522. I also wanted to bias the TIA from the noninverting terminal as shown in the figure below. I was simulating it in LTspice and I saw that the voltage was getting clipped at the load. Can anybody kindly suggest … Operational Amplifiers (Op Amps)amplifiershardwareADA4522-1Zero-Drift Op Ampsada4522ADA4522-2ARMZ MSL ratingForum ThreadAnswered Operational Amplifiers17 September, 2023Hi, what is the MSL rating for ADA4522-2ARMZ zero drift opamp? Can I consider the peak reflow temperature for the device as 300°C according to Table 5 of the datasheet? Datasheet/Specsada4522ADA4522-1 offset voltageForum ThreadAnswered Operational Amplifiers24 May, 2023Hi, Selected ADA4522-1 OPAMP as an amplifier. supply voltages: +12V and -12V Chose this OPAMP due to very less offset voltage. Offset voltage information available for other supply voltages. Please clarify below points: 1. Is this IC suitable to use for differential supply voltage of +/-12V? 2. Offset voltage … Operational Amplifiers (Op Amps)Datasheet/Specsoffset voltageamplifiersADA4522-1Zero-Drift Op AmpsCurrent source with ADA4522-2 and LT6657 (2.5V) | worse noise with higher load resistanceForum ThreadAnswered Operational Amplifiers12 December, 2022I have been using the attached constant 1mA current source circuit for quite some time to drive 4-wire RTD sensors.The circuit uses an LT6657-2.5 reference and an ADA4522-2 op amp to ensure 2.5V is driven across a source-side 2.5k set resistor.This … Operational Amplifiers (Op Amps)ADA4522-2 and LT6657 (2.5V)ada4522-2amplifiershardwareLow Power Op Amps (≤ 1mA/amp)Series Voltage Referenceslt6657voltage referencesADA4522 USE OF LARGE SOURCE RESISTANCEForum ThreadAnswered Operational Amplifiers16 November, 2022HelloIn the "USE OF LARGE SOURCE RESISTANCE" chapter of the ADA4522 datasheet, it states "When the ADA4522-1/ADA4522-2/ADA4522-4 are configured in a unity-gain follower configuration with a large source resistance and slow power supply ramp rate, The amplifier output may rail to the positive supply … hardwareamplifierada4522ADA4522-4 wrong output voltageForum ThreadAnswered Operational Amplifiers09 May, 2022Hi, I am using the Channel D of ADA4522-4 as a voltage buffer. For testing, I short the inverting input of channel D to the output of channel D. I apply -10V to the non-inverting input of channel D. My positive supply voltage is at 13.5V and … Operational Amplifiers (Op Amps)amplifiershardwareZero-Drift Op AmpsbufferADA4522-4output voltageada4522Instability of the output signal ADA4522-2Forum ThreadAnswered Operational Amplifiers18 May, 2021Hi! I'm using the ADA4522-2 as a differential op-amp. According to the tests and simulation results in LTspice, the output differential voltage is approximately 24V. If you use a different operational amplifier, for example, OP2177, this problem disappears and the voltage is 2.5 V. There is … op2177Operational Amplifiers (Op Amps)ada4522-2amplifiersLow Power Op Amps (≤ 1mA/amp)ada4522ADA4522 voltage follower config with dual suppliesForum ThreadAnswered Instrumentation Amplifiers27 June, 2020using an ADA4522 (dual pack) for a buffer/inverter setup. so, one of theamps setup as typical volt follower, the other a inverting amp. BOth are driven from an AD8221. The AD8221 is outputting a 20KHz sine biased at 2V. Vpp on sine = 2V... When I sweep the freq up … amplifiersInstrumentation Amplifiersad8221ADA4522 internal oscillatorForum ThreadAnswered Other Products (EN)18 March, 2020Hello My customers are suffering from 124MHz and 63MHz unwanted radiation appearing on the board.My customers are exhaustively checking the device's internal oscillator on the board.If you have any material that reassures my customers about the ADA4522, please let me know.Of course, if you know the … ada4522 <<<1234567>>>