Magnifying Glass Icon close icon

You searched for “AD5111.”

Filters

Filter Icon

Filters

Expand or Collapse Filter Icon
Expand or Collapse Filter Icon
Product Categories
Expand or Collapse Filter Icon
Resources
Expand or Collapse Filter Icon
Site Section
  • 1
Expand or Collapse Filter Icon
Result Type
  • 1
  • 65
  • 418
  • 169
  • 1
Expand or Collapse Filter Icon
Groups, Forums & Libraries
  • 1
  • 2
  • 1
  • 1
  • 21
  • 1
  • 1
  • 2
Expand or Collapse Filter Icon
Author
  • 46
  • 7
  • 13
  • 11
  • 22
  • 26
  • 77
  • 8
Expand or Collapse Filter Icon
Tag
  • 82
  • 71
  • 68
  • 45
  • 45
  • 39
  • 39
  • 37

Results on Analog.com

1
Relevance

Sort by

  • Product_categories.lvl0:Clock and Timing
Clear All Filters Icon
External Link Icon Right Arrow Icon External Link Icon External Link Icon Tag
  1. MT-200: Minimizing Jitter in ADC Clock Interfaces
    Tutorial

    PDF

    447 kB

  • <<
  • <
  • 1
  • >
  • >>

Results on EngineerZone

654
    Clear All Filters Icon

    1. AD5111 Writing issue

      Forum Thread
      Answered
      Switches/Multiplexers
      28 May, 2015
      Hello, One of my customers is using the AD5111 digital potenziometer. He has an issue with writing to his egisters Their tining is according to the figure 3 in the data sheet The CS is tied to "low" by pull down. During this cycle the CLK is in HIGH The …
      D/A Converters (DAC)ad5111Digital Potentiometers (DigiPOT)

    2. AD5111, shutdown mode

      Forum Thread
      Answered
      Precision DACs
      26 November, 2013
      Hi, I had a question on AD5111 shutdown mode which is described in datasheet page 18 (Rev.B) as follows. The AD5111/AD5113/AD5115 return the wiper to prior shutdown position if any other operation is performed. Q-1) What is the meaning of "prior shutdown" ? Is it indicating prior …
      D/A Converters (DAC)ad5111Digital Potentiometers (DigiPOT)

    3. AD5111, AD5113, AD5115: Shutdown mode

      Docs & FAQs
      Data Converters
      QuestionAD5111, AD5113, AD511: How can I put the chip in Shuntdown mode?AnswerThe command for SHUTDOWN MODE is sent by a low-to-high transition on the U/D pin, when CLK is high and CS is enabled. The command is executed on the CLK negative edge, as shown in …
      data convertersad51112CST0302

    4. AD5111, AD5113, AD5115: Shutdown mode

      Docs & FAQs
      Precision DACs
      Q AD5111, AD5113, AD511: How can I put the chip in Shuntdown mode? A The command for SHUTDOWN MODE is sent by a low-to-high transition on the U/D pin, when CLK is high and CS is enabled. The command is executed on the CLK negative edge, as …
      ad5113ad5115ad5111

    5. AD5111 is broken?

      Forum Thread
      Answered
      Precision DACs
      15 April, 2022
      Hello. I designed our product by applying AD5111 (10K, Up/Down).It worked normally once or twice, but it is currently fixed at A-W 45 ohm and W-B 9.8K ohm, and does not respond to any commands.Sometimes when power is applied again, it becomes A-W …
      D/A Converters (DAC)ad5111Digital Potentiometers (DigiPOT)

    6. AD5111: FAQ

      Docs & FAQs
      Data Converters
      AD5111: FAQ

    7. RE: AD5111 is broken?

      Forum Reply
      Precision DACs
      25 April, 2022
      On your last query, please elaborate with a circuit diagram.

    8. RE: AD5111 is broken?

      Forum Reply
      Precision DACs
      25 April, 2022
      Until the AD5111 is powered up, the relay control SW_COMP_VDIV_FCC is set to high (5V) and no signals are applied on A, W, B terminals. Is that correct? -> Yes. What are the voltages on the sens_1, sens_2 and sens_3 signals? -> sens_2 = 0.2V …

    9. RE: AD5111 is broken?

      Forum Reply
      Precision DACs
      20 April, 2022
      Until the AD5111 is powered up, the relay control SW_COMP_VDIV_FCC is set to high (5V) and no signals are applied on A, W, B terminals. Is that correct? What are the voltages on the sens_1, sens_2 and sens_3 signals? What is the SW_COMP …

    10. RE: AD5111 is broken?

      Forum Reply
      Precision DACs
      19 April, 2022
      Hi, vsethia. Thank you for your kindness.I answer your question as follows. 1. Please share the circuit diagram and the power supply sequencing details. -> Power is supplied directly from AD/DC 5V power.The sensor signal(A/sens_2, W/sens_1, B/sens_3) connection is controlled using …