Magnifying Glass Icon close icon

Filters

Filter Icon

Filters

Expand or Collapse Filter Icon
Expand or Collapse Filter Icon
Product Categories
Expand or Collapse Filter Icon
Resources
Expand or Collapse Filter Icon
Industry Solutions
Expand or Collapse Filter Icon
Technology Solutions
Expand or Collapse Filter Icon
Site Section
  • 1
Expand or Collapse Filter Icon
Result Type
  • 15
  • 3,174
  • 49,947
  • 457,848
  • 270,298
  • 670
Expand or Collapse Filter Icon
Groups, Forums & Libraries
  • 10,454
  • 8,907
  • 12,815
  • 13,145
  • 11,025
  • 23,016
  • 8,102
  • 9,154
Expand or Collapse Filter Icon
Author
  • 53,642
  • 2,476
  • 3,200
  • 6,142
  • 2,596
  • 34,378
  • 5,540
  • 3,580
Expand or Collapse Filter Icon
Tag
  • 27,633
  • 26,777
  • 26,296
  • 19,240
  • 16,171
  • 13,968
  • 13,767
  • 12,190

Results on Analog.com

1
Relevance

Sort by

  • Industry_solutions.lvl0:Automotive Solutions > Electrification and Powertrain Solutions
  • Technology_solutions.lvl0:Industrial Vision Technology
Clear All Filters Icon
External Link Icon Right Arrow Icon External Link Icon External Link Icon Tag
  1. Increase Productivity with Modular Mobile Robotics
    Video
    Oct 23, 2023
    1:49
    See mobile robot demo showcasing our extensive portfolio of modular solutions for industrial mobile robot that address the complexity of designing mobile robots and improve perception.
    Increase Productivity with Modular Mobile Robotics
  • <<
  • <
  • 1
  • >
  • >>

Results on EngineerZone

781,954
    Clear All Filters Icon

    1. ADMX2001B SPI control.

      Forum Thread
      Answered
      FPGA Reference Designs
      23 April, 2025
      I'm testing the SPI interface. When I power on and input the commands (wr, measure), (rd, FIFO read) and (rd, status), I believe the SPI protocol code in my FPGA works well(figure1). However, other commands do not work. For example, when I power on and input commands like …
      hardwareADMX2001

    2. Design advice for using ADR3650 to power a bridge sensor load cell data acquisition system and act as an ADC/DAC voltage reference...

      Forum Thread
      Answered
      Voltage References
      22 April, 2025
      Hello, I'm looking into using the ADR3650 as the excitation source and voltage reference in a data acquisition application with a bridge sensor (e.g. a mV/V load cell). My basic design is to use the ADR3650 to power the load cell, an AD8557 instrumentation amplifier an ADC …
      amplifiershardwareInstrumentation AmplifiersSeries Voltage Referencesvoltage referencesADR3650

    3. special character () in X subcircuits

      Forum Thread
      Answered
      LTspice
      21 April, 2025
      Hi, this is on 24.1.0, 24.1.6 and 24.1.7 on linux under wine. I noticed something strange when adding components implemented as an X-prefix subcircuit, such as TRIAC, opamp, SCR. I would expect a numeric suffix like 'X1' , X2 etc but instead seeing "X …
      software24.1.7LTspice

    4. Half-Bridge simulation

      Forum Thread
      Answered
      StudentZone (Analog Dialogue)
      21 April, 2025
      Hello , I'm trying to simulate a half bridge circuit with LTspice , for that I've defined my Vdd=Vcc=12V but when I choose the inputs LIN and HIN to be 5 V because I will bring them from a microcontroller I find an error . Here is my shematic
      hardwaremosfetLTspiceanalog circuit design

    5. ADF5901 OUTPOU POWER

      Forum Thread
      Answered
      RF and Microwave
      20 April, 2025
      During my recent use, I noticed that the TxAMP CAL REF CODE contains 8 bits, ranging from 0 to 255. However, the diagram in datasheet only shows values from 0 to 100. Is it because there is no change after 100, so it was not included? Additionally, I would like …
      hardwareMicrowave and mmWave TransmittersRF Integrated Transmitterspower amplifiersadf5901rf amplifiers

    6. ADF4159 AUX

      Forum Thread
      Answered
      RF and Microwave
      20 April, 2025
      If I use the ADF5901 or another chip along with the ADF4159 to generate a chirp signal, I know that if I connect AUX and AUXB to RFINA and RFINB, a differential 100-ohm microstrip line is required. Would it be possible to connect only one of these paths? For …
      hardwareMicrowave and mmWave TransmittersRF Integrated TransmittersFractional-N PLLadf4159Phase Locked Loop (PLL) Synthesizer &amp; Translation Looprf and microwave

    7. AD9542 M-Divider minimum value

      Forum Thread
      Answered
      Clock and Timing
      20 April, 2025
      Hi, I have just been reviewing our driver code for the AD9542 and I have only just spotted in the Register Map Reference Manual that the APLL M-dividers ( & ) have a clause saying the allowable values are 14 to 255. To be clear, up to now, our calculations were focussed …
      Datasheet/SpecsClock Generation and DistributionM-divider rangeAD954Clock SynchronizationAD9542

    8. Request UCL Key Converter for Secure ROM Bootloader Tools v1.0.0

      Forum Thread
      Answered
      Precision Microcontrollers
      20 April, 2025
      Hi ADI Support, I need the UCL key converter utility for MAX32560 Secure ROM Bootloader Tools v1.0.0. Please provide the executable and any usage instructions. Thanks!
      softwaremicrocontrollersCRKProcessors and MicrocontrollersMAX32560

    9. .OP point found by inspection related error in LTSpice

      Forum Thread
      Answered
      LTspice
      19 April, 2025
      Hi, I'm an student and I'm trying to make a simple full bridge rectifier with a load resistor and a capacitor. The simulation works with a 1uF capacitor, but when I change it to a 10 uF capacitor the simulation fails with this log: Start Time: Fri Apr …
      simulation24.1.7 x64softwareanalog circuit simulationLTspicesoftware problems

    10. Failed Ethernet Compliance Tests 10 Base-T using ADIN1200 evaluation board with Link Partner

      Forum Thread
      Answered
      Embedded Ethernet Switches
      18 April, 2025
      Hi ADI experts, I am using EVAL-ADIN1200FMCZ to do the 10 base-T compliance test, but the result failed. Attached the failed test report for your reference. And below picture is the default configuration on the evaluation board: PDF Many thanks. SK.
      hardwareIndustrial Ethernet SolutionsADIN1200Industrial Ethernet Physical Layer Devices